New Olympus Omniscan MX2 32 : 128 PA Flaw Detector 

The OmniScan MX2 offers a high acquisition rate and new powerful software features for efficient manual and automated inspection performance—all in a portable, modular instrument.

The OmniScan MX2 simplifies and speeds up the setup process with its intuitive Weld Overlay software feature, so you can start testing immediately. Featuring the industry-standard phased array user interface with faster-than-ever performance, a bigger and brighter 10.4 inch screen, new and unique intuitive touch-screen capabilities, and faster data transfer, enabling you to get to your next inspection quicker.

More than an Instrument —A Solution Provider

The OmniScan MX2 is an important part of your inspection solution, and can be combined with other critical components to form a complete inspection system. Olympus offers a complete product range that includes phased array probes, scanners, analysis software, and accessories, all of which are integrated and packaged into rapidly deployable, application specific solutions for quick returns on your investment. In addition, Olympus offers a high-quality calibration and repair service worldwide, that is backed by a team of phased array application experts to ensure that you get the support you need.

Weld Inspection of Small-Diameter Pipes

When coupled with the COBRA manual scanner, the OmniScan flaw detector is capable of inspecting pipes ranging from 0.84 inch OD to 4.5 inch OD. With its very slim design, this manual scanner is able to inspect pipes in areas with limited access.

Pressure Vessel Weld Inspection

A complete inspection of pressure vessel welds can be performed manually, or in a single scan using an OmniScan and a scanner for a turnkey solution. Inspection results are available immediately, enabling you to detect problems with welding equipment and fix them right away

Composite Inspection

Olympus offers complete solutions for the inspection of carbon-fiber reinforced polymer structures. These solutions are based on the OmniScan flaw detector, the GLIDER scanner, and dedicated probes and wedges designed for CFRP flat panel and radius inspection.

Corrosion Mapping Inspection

The OmniScan PA system with the HydroFORM scanner is designed to offer the best inspection solution for the detection of wall-thickness reductions resulting from corrosion, abrasion, and erosion. For this application, phased array ultrasound technology offers superior inspection speed, data point density, and detection.

Specifications:

Overall dimensions (W x H x D)	325 mm x 235 mm x 130 mm (12.8 in. x 9.3 in. x 5.1 in.)
Weight	3.2 kg (7 lb), no module and one battery
Data Storage
Storage devices	SDHC card, most standard USB storage devices, or fast Ethernet
Data file size	300 MB
I/O Ports
USB ports	3
Speaker out	Yes
Video output	Video out (SVGA)
Ethernet	10/100 Mbps
I/O Lines
Encoder	2-axis encoder line (quadrature, up, down, or clock/ direction)
Digital input	4 digital TTL inputs, 5 V
Digital output	4 digital TTL outputs, 5 V, 15 mA
Acquisition on/off switch	Remote acquisition enabled TTL, 5 V
Power output line	5 V, 500 mA power output line (short-circuit protected)
Alarms	3 TTL, 5 V, 15 mA
Analog output	2 analog outputs (12 bits) ±5 V in 10 kΩ
Pace input	5 V TTL pace input
Display
Display size	26.4 cm (10.4 in.) (diagonal)
Resolution	800 pixels x 600 pixels
Brightness	700 cd/m2
Number of colors	16 million
Type	TFT LCD
Power Supply
Battery type	Smart Li-ion battery
Battery life	Minimum 7 hours with two batteries
Environmental Specifications
Operating temperature range	-10 °C to 45 °C (14 ºF to 113 ºF)
Storage temperature range	–20 °C to 60 °C (–4 ºF to 140 ºF) with batteries –20 °C to 70 °C (–4 ºF to 158 ºF) without batteries
Relative humidity	Max. 70% RH at 45°C noncondensing
Ingress Protection Rating	IP54
Shockproof rating	Drop-tested according to MIL-STD-810G 516.6
Phased Array Module Specifications (Applies to OMNI-M-PA32128)
Voltage	Low: 45 V High: 90 V
Pulse width	Adjustable from 30 ns to 500 ns; resolution of 2.5ns
Fall time	<5 ns
Pulse shape	Negative square pluse
Output impedance	<30 ohms
Receiver
Gain range	0 dB to 74 dB in steps of 0.1 dB, maximum input signal 1.25 Vp-p
Input impedance	50 Ohms
System bandwidth	0.53 MHz to 21 MHz +10% (-3 dB)
Beam formation
Scan type	Sectorial and linear
Aperture	32 elements
Number of elements	128 elements
Number of focal laws	256
Delay range transmission	0 us to 10 us in 2.5 ns increments
Delay range recetption	0 us to 10 us in 2.5 ns increments
Acquisition Specifications
Frequency
Digitizing frequency	100 MHz (10 Bits)
A-scan (acquisition mode)	Up to 6000 A-scans per second (512-point, 8-bit A-scan)
Maximum pulsing rate	Up to 10 KHz (C-scan)
Depth in material	59.8 meter in steel (longitudinal wave), 10 ms in with compression 0.49 meter in steel (longitudinal wave), 81.9 us without compression
Display
Refresh rate	A-scan: 60 Hz; s-scan: 20 Hz to 30 Hz
Envelope (echo-dynamic mode)	Yes: Volume-corrected S-scan (30 Hz)
Synchronization
On internal clock	1 Hz to 10 kHz
External pace	Yes
On encoder	on 2 Axes: from 1 step to 65536 steps
Data Specifications
Number of data points	Up to 8000
Real-time averaging	2, 4, 8, and 16
Rectification	RF, full wave, half wave+, half wave-
Filtering	Low-pass (adjusted to probe frequency), digital filtering (bandwidth, frequency range)
Video filtering	Smoothing (adjusted to the probe frequency range)
Programmable TCG
Number of points	16: one TCG(time-corrected gain) curve per channel for focal laws
Storage
A-scan recording	6000 A-scans per second (512-point, 8-bit A-scan)
C-scan recording	I, A, B, up to 10 kHz
Maximum file size	Limited to available internal flash memory; OmniScan MX2: 300MB

Include in the box:

Olympus OmniScan MX2 32:128 Phased Array Flaw Detector 

Battery Pack

AC Adapter/Charger

Power Cord

User Manual On Cd-ROM

Carrying Case (G)